What Zone are we in?
Canada is split up into 3 zones, 1 through 3. The majority of Saskatchewan is Zone 2 & 3. Refer to the map to see which Zone you are located in.
What is the difference between dual pane and triple pane glazing?
There is a significant difference in insulating value as well as sound dampening between dual pane & triple pane glass. A standard dual pane glass unit with low-e and Argon gas has an R-value of 4.16, where as a triple pane glass unit with one coat of low-e and one Argon gas filled air chamber has an R-value of 5.56. The R-value of a triple pane glass unit can further be improved by having two low-e coatings and both air chambers filled with Argon gas, to ultimately achieve an R-value of 8.33.
How long does it take to have a window made?
A standard window takes 3-4 weeks for us to complete. Specialty windows such as Bays, Bows, Radius, etc… are completed in 4-6 weeks.
Does EnerGuard measure windows or perform installations?
EnerGuard Windows & Doors Inc. is a wholesale manufacturer that distributes its products by way of factory approved contractors. Contractors are chosen for their keen attention to detail and quality. Contractors are experts in their field and strive to complete your project right, THE FIRST TIME, and without voiding the manufacturer’s warranty.
How do I get a quote for windows?
A quote can be requested by following the Request a quote now! buttons, which are conveniently located throughout our web site.
Do the different coatings really make a difference in how the window performs?
Yes they do. Three types of glass options are available with most of our window systems – EG-S2, EG-S3, & EG-S3+ . Each has unique characteristics that help them perform for specific applications. Please check out our Glass section for more information and to view the energy performance of each of the glass options available.
How is EnerGuard different than any other manufacturer?
EnerGuard is proudly locally owned and operated. We offer what the national brands can offer, but with a more personal touch. Our design team is dedicated to educating customers and dealers on all of our options and how those options will ultimately affect the performance of your windows. We maintain a consistent quality control program and continually maintain on-time delivery schedules. EnerGuard manufactures an exceptional and solid product that we are proud to call our own.
What causes condensation on windows?
Condensation is water that forms when warm, moist air hits a cooler surface. In homes, it might occur on surfaces such as windows, bathroom walls and cold-water pipes. When interior humidity levels are too high relative to cooler outdoor temperatures, condensation can form on the coldest surface in a room – often the glass in a window or door. While windows and doors do not cause condensation, they may be one of the first places it shows up. For tips on how to control condensation on windows, please refer to our Warranty and Maintenance guide.
What do the A’s, B’s and C’s mean when considering windows?
All windows must be rated for their air-tightness, water-tightness, and wind load strength. National, Provincial and local building codes require that windows meet these minimum standards of performance. The A, B & C ratings refer to these attributes as shown below.
| AIR TIGHTNESS RATINGS (“A” RATING) | ||
| Max. Air Leakage Rate (m³/h/m) |
||
| A1 | 2.79 | |
| A2 | 1.65 | |
| A3 | 0.55 | |
| WATER TIGHTNESS RATINGS (“B” RATING) | ||
| Pressure Differential (Pa) |
Equivalent Wind Speed (Kph) |
|
| B1 | 150 | 55 |
| B2 | 200 | 60 |
| B3 | 300 | 75 |
| B4 | 400 | 85 |
| B5 | 500 | 100 |
| B6 | 600 | 110 |
| B7 | 700 | 120 |
| LOAD-RESISTANCE RATINGS (“C” RATING) (to blow-out) |
||
| Pressure Differential (Pa) |
Equivalent Wind Speed (Kph) |
|
| C1 | 1500 | 175 |
| C2 | 2000 | 200 |
| C3 | 3000 | 250 |
| C4 | 4000 | 280 |
| C5 | 5000 | 325 |
EnerGuard windows have been certified to meet and exceed Canada’s National Building Code standards (i.e. on average, our air leakage rate is .03 m³/h/m, far exceeding the minimum requirements).
Installation
A knowledgeable professional should install windows according to the manufacturer’s instructions. A poorly installed product may not operate properly and could cause cold drafts even though the product itself is energy efficient. Poor installation may also allow water to leak into the home, leading to costly repairs.
WINDOW INSTALLATION INSTRUCTIONS
Important: All window units are factory fitted and assembled. ON SITE FITTING IS NOT REQUIRED, so long as windows are Plumb, Level, Square and shimmed correctly within the opening.
Rough Openings:
- The hole in the wall should be 1” wider and 1” higher then the outside measurement of the frame when using a brickmould (3/4” wider and 3/4” higher when using a Nailing Flange).
- The bottom plate of the opening must be level with no dips or crowns.
- The sides of the wall opening must be parallel.
Installation:
- Before placing the unit in the opening, a bead of good quality caulking must be applied to the perimeter of the opening on the exterior side of the sheathing. Ensure that when the unit is installed that the caulking comes in contact with the backside of the brickmould or nailing flange forming a water tight seal.
- Place the unit in the opening maintaining the same clearance all around.
- Temporarily shim and anchor the unit at the sill and then at the head, maintaining the same margin (clearance) between the sash and the frame at the side and top.
- The unit should then be temporarily shimmed and anchored up the sides of the unit maintaining a constant margin all the way up the sash.
- Once the unit is permanently shimmed and fastened with consistent margins the sash should operate freely and the two lock side corners should seal tightly.
- Fastening the unit should be done through the brickmould, jambs or nailing fin.
- Multiple wide window units should be shimmed under the sill of the unit at the jamb, all mullions and every 12” where the mullion is not involved.
- Lightly pack insulation in the void between the window unit and frame and the rough opening.
- When brickmould, or a nailing flange is supplied loose, be sure to apply caulking to the channel where the brickmould, or nailing flange fits into and any surface joint to prevent water penetration.
- Adequate flashing must be installed across the top of the unit to prevent water penetration.
CAUTION
- It is the owner, builder or architects responsibility to ensure all products selected are in compliance with applicable laws and building codes.
- All units should be lifted from the bottom of the unit. Do not pull or lift the unit using the brickmould, nailing flange or jambs as this may cause structural damage to the unit and/or the seal, affecting the windows performance.
- The use of some expanding foam insulations can cause the frame to bow. Please use extreme caution when using any expanding foam products.